PIC16F873T-04E/SO【PDF 23/218 页】IC MCU FLASH 4KX14 EE 28SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3889

19页 20页 21页 22页 [23页]24页 25页 26页 27页

2001 Microchip Technology Inc.

DS30292C-page 117

PIC16F87X

11.5

A/D Operation During SLEEP

The A/D module can operate during SLEEP mode. This

requires that the A/D clock source be set to RC

(ADCS1:ADCS0 = 11). When the RC clock source is

selected, the A/D module waits one instruction cycle

before starting the conversion. This allows the SLEEP

instruction to be executed, which eliminates all digital

switching noise from the conversion. When the conver-

sion is completed, the GO/DONE bit will be cleared and

the result loaded into the ADRES register. If the A/D

interrupt is enabled, the device will wake-up from

SLEEP. If the A/D interrupt is not enabled, the A/D

module will then be turned off, although the ADON bit

will remain set.

When the A/D clock source is another clock option (not

RC), a SLEEP instruction will cause the present conver-

sion to be aborted and the A/D module to be turned off,

though the ADON bit will remain set.

Turning off the A/D places the A/D module in its lowest

current consumption state.

11.6

Effects of a RESET

A device RESET forces all registers to their RESET

state. This forces the A/D module to be turned off, and

any conversion is aborted. All A/D input pins are con-

figured as analog inputs.

The value that is in the ADRESH:ADRESL registers is

not

modified

for

Power-on

Reset.

The

ADRESH:ADRESL registers will contain unknown data

after a Power-on Reset.

TABLE 11-2:

REGISTERS/BITS ASSOCIATED WITH A/D

Note:

For the A/D module to operate in SLEEP,

the A/D clock source must be set to RC

(ADCS1:ADCS0 = 11). To allow the con-

version to occur during SLEEP, ensure the

SLEEP

instruction immediately follows the

instruction that sets the GO/DONE bit.

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Value on

POR,

BOR

Value on

MCLR,

WDT

0Bh,8Bh,

10Bh,18Bh

INTCON

GIE

PEIE

T0IE

INTE

RBIE

T0IF

INTF

RBIF

0000 000x

0000 000u

0Ch

PIR1

PSPIF(1)

ADIF

RCIF

TXIF

SSPIF

CCP1IF

TMR2IF

TMR1IF

0000 0000

8Ch

PIE1

PSPIE(1)

ADIE

RCIE

TXIE

SSPIE

CCP1IE

TMR2IE TMR1IE 0000 0000 0000 0000

1Eh

ADRESH

A/D Result Register High Byte

xxxx xxxx

uuuu uuuu

9Eh

ADRESL

A/D Result Register Low Byte

xxxx xxxx

uuuu uuuu

1Fh

ADCON0

ADCS1

ADCS0

CHS2

CHS1

CHS0

GO/DONE

—

ADON

0000 00-0

9Fh

ADCON1

ADFM

—

PCFG3

PCFG2

PCFG1

PCFG0

--0- 0000

85h

TRISA

—

PORTA Data Direction Register

--11 1111

05h

PORTA

—

PORTA Data Latch when written: PORTA pins when read

--0x 0000

--0u 0000

89h(1)

TRISE

IBF

OBF

IBOV

PSPMODE

—

PORTE Data Direction bits

0000 -111

09h(1)

PORTE

—

RE2

RE1

RE0

---- -xxx

---- -uuu

Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used for A/D conversion.

Note

These registers/bits are not available on the 28-pin devices.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式